Tires are the only contact point we have with the road, as they are the
key to propelling and stopping your car. We rely on that small patch of
rubber that is at each of the four corners of the car, to keep us on the
road. It is important that we make sure that they are the proper tires,
inflated, in good condition, wearing properly, and not too old.
Proper Tire
Car manufacturers choose specific tires to be fitted on their cars. They
take into consideration what the vehicle was built for, its maximum performance,
and weight loads. After determining these factors, they choose a tire
that best fits the car’s needs. It is important to have these same
considerations when we replace our tires. Choosing the wrong tire can
have severe consequences. In the 1990’s, there were many cases where
the manufacturer made the wrong tire choice leading to people losing their
lives. It is crucial to go to a tire professional to help pick the right
tires for your vehicle.
Proper Tire Inflation
Tire inflation is important for three reasons, handling, comfort, and fuel
efficiency. Automotive manufactures have recommended tire inflation posted
for your vehicle. The recommendations are based on the optimal pressure
for two reasons. The higher the tire pressure, there is less rolling resistance,
higher fuel efficiency, a rougher ride, and less traction. On the other
hand, the lower the pressure, the better the traction, smoother ride,
but there is poor fuel economy, and poor wear. They believe there should
be a balance of good fuel economy, smooth ride, and ideal handling. Manufacturers
usually put a sticker with pressures near VIN. label at B pillar or on
the fuel door. There is a choice for a fully loaded or partially loaded
car. Choose the inflation that best suits your needs.
Good Condition and Tracking Properly
To keep up with your tire’s wear, look for four things. Look for
how deep is the thread, your vehicle's alignment, tire balance, and damage.
Thread is what the tire manufactures use to move water from under your
tire. Without it a tire would hydroplane and slide all over the road.
Minimum thread depth on a standard road car is 3/32 of an inch. That is
the minimum depth you want to see anywhere on the tire. One part of the
tire may show considerably more, but it could be down to the steel belts
elsewhere. It is important when checking a tire, you check the full width
of the tire. The easiest way to measure the full width is to use a penny.
Take a penny place it on edge with Lincoln’s head pointing in towards
the tire. If the top of President Lincoln’s head is visible, then
your tire is worn. All four tires should be examined and make sure to
sample the complete circumference of the tire. Uneven tread wear is usually
a sign of an alignment problem. Alignment is how we keep your vehicle
tracking straight. If a tire is worn more on the inside or outside edge,
it could mean your alignment is out of adjustment. Sports cars tend to
have aggressive alignments and excessive wear in one part of the tire
is to be expected. Sports car manufactures use alignment to allow their
cars to handle better at higher speeds and side loads. The compromise
of this is premature tire wear, usually on the inside edge. You may see
a near perfect outer thread pattern and a severely worn inner one. Therefore,
it is important to always check the full width of the tires.
If a tire is not properly balanced, the result will be a vibration that
can be felt through the car or steering. Usually it’s a 5 mph range
that you feel the vibration (e.g. 65 mph to 70 mph). This is commonly
mistaken as an alignment problem. If not properly addressed, this can
lead to scalloping of the tread and noisy tires.
Make it a semi-regular practice to check your tires for damage. Damage
can come in the form of punctures (nails, screws, glass, rocks, etc.),
sidewall damage from curbs, or bubbles. Bubbles occur when your tire begins
to delaminate. Your tires are constructed of numerous plies of rubber
and steel wire. Delamination is usually caused by an impact such potholes,
running over bumps, or objects in the road, that causes the belts of the
tire to tear, or age (which we will discuss in greater detail in the next
section). At that point, the belts are compromised and can no longer hold
its shape. An air pocket will form between belts and rubber tread, which
may also be felt as a vibration.
Tire Age: How Old is too Old?
Two frequently asked questions, are how can you tell how old a tire is
and what’s wrong with an old tire. Tires have “Born On Dates”
which are production dates. They usually appear in an oval on the sidewall
and consist of 4 numbers such as 1508. The first pair of numbers is the
week in which the tire was made and the second pair is the year. For the
number 1508 stands for the 15th week of 2008 or April 7-13, 2008. When
buying new tires, it is a good idea to find out what is the production
date of the tires you are buying, so you have a record of when your tires
were produced. Tire manufactures and vehicle manufactures opinions vary
on how old is too old. Six to eight years is a good timeframe to consider
replacing your tires, despite how much tread is left on them. Contributing
factors of tires aging are heat and humidity. As they age, tires will
begin to break down and delaminate. Inspect your tires to see if you can
see cracks in the sidewall, check the born on date, and most importantly,
have a tire professional inspect your tires, and follow their recommendations.
Importance of Tire Maintenance.
Tire maintenance is important on many levels, as it is the only contact
the vehicle has with the road. Efficiency and proper inflation can increase
your fuel mileage. It is economically efficient to make sure your tires
are properly inflated, balanced, and suspension aligned can extend the
life of your tire. Most importantly if there is ever a question about
your tires, ask a qualified tire expert to help you make the proper decisions.
So much is riding on four little rubber contact patches and you should
make the right choices.